Possible Cause: Door is not closed properly

Solution: Open and then close the door properly

Possible Cause:

• Water tap turned off
• Water supply not available
• Sieve/filter blocked in water inlet hose
• Water pressure too low
• Bent/damaged Water inlet hose

Possible Cause:

• Power supply cable plug not fitted properly to the socket
• Power supply rating is not suitable

Solution:

• Fit the plug properly/replace the socket with standard one
• Connect to 230 V, 15 A, 50 Hz. Single phase A.C. supply with proper earthing

Possible Cause: Overloading of washing machine

Solution:The washer restarts after about 30 min

Possible Cause: Programme time is extended due to low inlet water temperature / low input voltage

Possible Cause:

• Coin trap is blocked
• Exhaust hose clogged/bent

Solution:

• Clean Coin trap
• Clean the exhaust hose / Remove bend.

If the error message could not be solved with the aid of the above table: *Switch OFF the appliance > *Wait for 15 seconds > *Switch ON the appliance  > *Select and start a program

If the error message repeats, please call service personnel.

Possible Cause: At rinse hold step this code will toggle

Solution: Press start/pause button or select drain program

Possible Cause: Code will be displayed during delay start mode

Possible Cause:P01, P02…P15 in the display denotes the chosen program. In case the selector switch is rotated during a program the original selected program denotion will toggle along with remaining time

Solution: Shift the program selector position to its original program position which is presently running

Possible Cause:Door not closed properly. Door not locked

Solution: Open and then close the door properly

Probable Cause: Laundry load is unbalanced

Solution:If laundry load is small. It can lead to an unbalanced condition. Add 1-2 similar items to help balance the load and rearrange load to allow proper spinning.

Possible Cause: Door not getting unlocked

Solution: Switch the program selector to OFF position. Wait for 2 minutes and check if the door can open. Do not try to open the door forcibly. If the door cannot open or if the same message is displayed switch OFF the appliance and contact IFB Care

Possible Cause:

• Water tap turned OFF.
• Water supply not available or low water pressure.
• Sieve/filter blocked in water inlet house.
• Bent/damaged water inlet hose

Solution:

• Turn ON the tap.
• Washing Machine will start automatically on resumption of water supply
• Clean sieve filter
• Remove bend/damage

Possible Cause: Cloth trapped between drum and door area

Solution: Switch the program selector to OFF position and wait for 2 seconds. Run drain program. After end, rearrange the clothes and restart the required program. If the same message appears again, switch OFF the appliance and contact IFB Care

Possible Cause:

• Water not drained
• Filter is blocked
• Exhaust hose clogged/bent

Solution:

• Press Start/Pause button to restart the drain
• Switch OFF the appliance. Drain out the water using drain plug and then clean filter
• Clean exhaust hose/remove bend

Possible Cause: Water temperature is above 60C at the start of the program

Solution:

• Start New/Drain program once the water cools down to approximately 60C.
• Switch the program selector to OFF position, wait for 2 seconds and restart. If the same message appears again switch OFF the appliance and contact IFB Care

Solution: Switch the program selector to OFF position, wait for 2 seconds and restart. If the same message appears again switch turn OFF the tap, switch OFF the appliance and contact IFB care

Probable Cause: Input voltage is high

Solution: machine will start automatically after the voltage decreases to sade operating level. If this error display persists/occurs frequently then contact your electrician to locate the fault in the electrical system

Probable Cause: Input voltage is low

Solution:machine will start automatically after the voltage increases to sade operating level. If this error display persists/occurs frequently then contact your electrician to locate the fault in the electrical system.

Possible Cause: Cloth trapped between drum and door area

Solution: Switch the program selector to OFF position and wait for 2 seconds. Run drain program. After end, rearrange the clothes and restart the required program. If the same message appears again, switch OFF the appliance and contact IFB Care

• Check if the machine is ON.
• Check for loose connections in plug / socket
• Check if the programmer selector knob is in OFF position

• Check if machine is powered ON.
• Check if the “Start/Pause” button is ON. The LED will glow when it is pressed.
• Check water supply.
• Porthole door not closed properly

• Check if machine is powered ON.
• Check if the “Start/Pause” button is ON. The LED will glow when it is pressed.
• Check water supply.
• Porthole door not closed properly

• Check water supply
• Porthole door not firmly closed
• Water taps not turned on
• Bent inlet hose
• Sieve on inlet valve / inlet hose clogged.

• Detergent used is not a washing machine detergent
• Excessive detergent used

• Inlet/Outlet hose connection loose
• Coin trap not screwed on properly
• Inlet hose leaking

• Coin trap clogged
• Outlet hose end above 1 meter from floor level

• Check if the Spin speed selector knob is set to ‘No Final Spin’ position.
• Rinse Hold button is pressed.
• Coin trap is clogged.

• Machine not levelled properly
• Coin trap clogged partially.
• Clothes not loaded as instructed

• It is normal for noises to be heard while motor is running. However, wash load belt tension and motor mounting bolt should be checked for specified limits

• It is normal for noises to be heard from the pump during the start-up and final stage of draining. However, check for fluff filter clogging.

• Not a fault.
• It is normal as the washing time may vary depending upon the type and quantity of laundry, inlet water pressure, inlet water temperature, variations in power supply and other usage conditions.